Skip to content
DayRoute

How many delivery drivers do I need for my stops? A calculator

Updated

Short answer

Drivers needed = stops per day ÷ stops one driver can do in a shift, rounded up, plus spare drivers. Stops per driver = minutes left in the shift for stops ÷ minutes per stop (driving to it plus time at it), and no more than one van carries. Example with invented numbers: 300 stops a day at 9 minutes each (4 driving, 5 at the door) and 9-hour shifts with a 30-minute break and 60 minutes at the depot leave 450 minutes, or 50 stops per driver: 300 ÷ 50 = 6 drivers, plus 1 spare at 10% = 7. It is an estimate: time windows, traffic and where the stops are change the real number every day.

Not a route plan: averages hide the far-out stops, the tight time windows and the heavy orders, so use it to size a fleet, then plan each day with the real orders.

Drivers needed calculator

Every value below is an invented example, not an industry figure: replace each one with your own. The result updates as you type, and nothing you type leaves this page.

Drivers needed, spares included

7

Limited by shift time

Drivers on routes
6
Spare drivers
1
Stops per driver per day
50
Minutes for stops per shift
450
Stops per hour
6.7

How it works in DayRoute

The formula and its assumptions

One driver drives one van for one shift. Use averages from a normal day.

  • Minutes for stops = shift length × 60 − breaks − depot time. Depot time is loading plus the drive to the first stop and back from the last
  • Minutes per stop = minutes of driving to each stop + minutes at each stop; 60 ÷ minutes per stop is the stops per hour
  • Stops per driver = minutes for stops ÷ minutes per stop, rounded down, and no more than the stops one van carries in one trip
  • Drivers = stops per day ÷ stops per driver, rounded up; spare drivers = drivers × spare %, rounded up, for absences and busy days
  • It assumes the day’s stops can be split evenly between drivers and that every van does one trip a day

Worked examples by stops per day (invented numbers)

These numbers are invented to show the arithmetic. They are not benchmarks or results from any customer. The three columns differ in how far apart the stops are and how long each takes; in the third, the van is full before the shift runs out, so capacity sets the number. The 300-stop column is what the calculator opens with.

  • 100 stops at 10 minutes each: 45 stops per driver, 3 drivers, 4 with a spare
  • 300 stops at 9 minutes each: 50 stops per driver, 6 drivers, 7 with a spare
  • 1,000 stops at 7 minutes each: 64 stops by time but 60 by van, 17 drivers, 19 with spares
Minutes per stop (driving + at the stop)100 stops: 6 + 4 = 10300 stops: 4 + 5 = 91,000 stops: 3 + 4 = 7
Minutes for stops (9 h − 30 min break − 60 min depot)100 stops: 450300 stops: 4501,000 stops: 450
Stops per driver by time100 stops: 450 ÷ 10 = 45300 stops: 450 ÷ 9 = 501,000 stops: 450 ÷ 7 = 64
Stops one van carries100 stops: No limit300 stops: No limit1,000 stops: 60
Drivers on routes100 stops: 100 ÷ 45, rounded up = 3300 stops: 300 ÷ 50 = 61,000 stops: 1,000 ÷ 60, rounded up = 17
Spare drivers (10%, rounded up)100 stops: 1300 stops: 11,000 stops: 2
Drivers needed100 stops: 4300 stops: 71,000 stops: 19

What the calculator leaves out

Averages hide the stops that make a day hard. Use the result to size the fleet, then check it against real days.

  • Time windows: a stop that must be served between 9 and 11 a.m. can force waiting, or a second driver in the same area
  • Where the stops are: a few far-out stops cost much more driving than the average says
  • Weight and volume: a van can fill up by weight or space before it reaches its number of stops
  • Traffic and failed attempts: both take time that an average minutes per stop may not include

Where DayRoute fits

DayRoute is route planning and delivery management software for local delivery teams, made by EzOps. It plans a whole day for all drivers at once with time windows, capacity and shifts, and a stop that does not fit is left out with the reason, so you see on real orders whether your drivers are enough. Its analytics show stops per hour for the team and each driver, the input this calculator depends on most.

Frequently asked questions

Is the number of stops per driver a benchmark?

No. The calculator opens with invented example values. Measure your own minutes per stop, or stops per hour, and use those.

Where do I get minutes per stop?

From your own routes: route minutes divided by stops, or 60 divided by your stops per hour. DayRoute analytics show stops per hour for the team and each driver.

Why add spare drivers?

Drivers are off sick, on leave or needed on a busy day. Without spares, one absence leaves a route without a driver.

Does the calculator send my numbers anywhere?

No. It runs in your browser, and nothing you type is sent or stored.

More answers

Answers →

See whether tomorrow’s orders fit your drivers

Plan every driver’s route at once, with any stop that does not fit listed with the reason, on a 1-month free trial, no credit card.

Want a walkthrough with us? Book a demo